Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

Do me a favor and imagine that you are in need of suggestions for a Fourth of July party. You head to via Wikipedia

Of course, I’m not talking about snap pops, black cats, m-80s, or even those cool little paper cars that gush sparks, travel four feet, and then burn to death in a microblaze reminiscent of a 1970s action film.

I am talking about the ones that explode up there, the ones you have to tilt your head back to see. That the fireworks explode in the night sky is important because the very act of looking up immediately takes you out of the mundanity that the rest of the holiday will surely deliver – the planning, the decorating, the complications. No more overflowing trashcan with wing sauce-smeared cocktail napkins. No more ordinary stuff.

At the heart of the Fourth of July is a spirit of independence that is, actually, a big deal. When your eyes are on what’s going on at ground level, it can be hard to realize how big a deal ideas like independence and sacrifice are. Once your attention is arrested by the spectacle of fireworks happening up there in the sky, you’re taken out of the everyday and able to reflect on these things, which is important, I think.

2. They are glorious.

“And the rockets’ red glare/ The bombs bursting in air,” goes the song. Did you know that the word “rocket,” in the sense of the combustion-fueled projectile, dates all the way back to 1566? The Oxford English Dictionary notes that rockets have historically been “used for signalling, in maritime rescue, for entertainment, and as a weapon.” Fireworks symbolize communication, violence, and entertainment: A strangely fitting mix for the complex human heart.

The red glare of the rockets in “The Star-Spangled Banner” refers to the bombardment of Fort McHenry in the War of 1812. That the fort was not taken during the battle is indeed glorious, and fireworks are a reminder of the fortitude of the people who fought and suffered to keep America independent in 1776 and again in 1812. Boom. (Literally: boom!)

3. They are beautiful.

So, those are my three reasons that fireworks are the most important part of any holiday festivity: They happen above you; they are glorious; and they are beautiful. I think these are pretty good reasons for making sure you see some fireworks this Fourth of July.

Take a moment out of the hectic festivities to reflect on the spirit of rebellion, creativity, and inspiration that is involved in claiming and defending independence from parties eager to exploit the vulnerable. This is about more than just us. This unites us across time and space. Fireworks reflect the beauty of standing together for what is right, even when it hurts.

Everyone is looking for ways to save power.  Whether to save money or the planet, one of the best and most popular ways to save power on lighting is by installing dimmer switches to control your lights.  Besides saving power, they’re also great for setting the mood in your home.  More and more dimmer switches are being installed in American homes every year.

Dimmer switches are easy to install, even for an everyday person. Of course, even an easy installation can be problematic, so you should always contact the best Dallas electrician to ensure that you’re doing things right, or to perform the dimmer switch installation for you if you don’t want to take a chance of making a mistake.  Either way, here are some important do-it-yourself electrical tip to keep in mind about dimmer switches: