Outlets are wired into your home to make it convenient to plug in anything from an appliance to a lamp. However, an electrical fault can occur endangering your home. It’s not a good idea to have 19 different appliances plugged into a single outlet. This can cause a short; not to mention the maze of cords running through the room aren’t safe for family and pets.

Sometimes electrical faults in your system can cause a ceiling light or fan to stop working. After identifying that a bad bulb is not the culprit, you should turn off the power and inspect the light fixture itself. Check the cable and flex connections and make sure the terminal screws are tight. Use a continuity tester to make sure the flex hasn’t gone bad requiring a replacement.

Lights, fans, and other fixtures can also stop working because a residual current device has tripped. You can reset the device but if it trips again it’s best to call in a certified electrician.

If you are still experiencing problems after doing these simple troubleshooting tasks, it’s always best to call in a trained electrician. Outlets or lights that are malfunctioning could be caused by exposed wires somewhere in your electrical system. If your circuit breaker continually trips, it means the current in your home is not cycling as it’s intended. Either way, it’s much safer to have these issues repaired by a good electrician.

Light switches are so common we rarely think twice about them. We walk into a room, flip the switch without looking and carry on. In the middle of the night or first thing in the morning, the light that comes on in an instant is a bit of a shock to eyes that have not quite adjusted. Lights are often a little too much for certain occasions and you are forced to choose between too much or too little. Or are you? Your California electrician has a better idea. The team at The Electric Connection can help you take control of the light in your life by installing a dimmer switch.

For a long time, dimmer switches were a common feature for chandeliers installed in the dining room area. This allows you to dictate just how much light you want to shed over the dinner table. Cheery breakfasts and lunches are best served with plenty of light. Evening meals that are meant to help you unwind or connect with your friends and loved ones over a delicious entree are best served with low light. It gives the space a more intimate feel.

You can have that same luxury of light control in every room in the house. There is some very minimal electrical wiring that will need to be done. It is a fairly easy switch to install a dimmer in place of your existing light switch. You can have one in the living room that allows you to turn down the lights while you are watching television. Another in the bathroom gives you the ability to have low light for those middle of the night visits instead of blinding light that wakes you up and interrupts a good night’s sleep. An electrician in southern California is ready to help. Just give The Electric Connection a call today and schedule your dimmer switch installation.

When you need an electrician it can be difficult to scan through the listings online and pick just the right one. You just never know what you are getting. It’s not like there is an app for that. You need to have an idea of the qualifications you should look for before you hire somebody to come into your home and do work. Before you hire an electrician in Pasadena, follow these guidelines. You can always count on the team at The Electric Connection to meet each of these qualifications.

A licensed electrician is an absolute must. The company the electrician works for should also be licensed. A person who has gone through the licensing process gives means they have met certain knowledge requirements.

The company you hire should be bonded and insured. This protects you in case of an accident that damages your home or an accident the electrician suffers while on your property.

Reputation is very important when it comes to hiring an electrician. Pasadena homeowners will want to talk with others who have used the company’s services to find out if they were pleased with the work that was done. Electricians work hard to build up a solid reputation because they know how important it is to getting more work.

You will want a company that hires electricians who are reliable and will show up when they are scheduled. You have a busy life and need to be able to count on an electrician to be there on time and to complete the work in a reasonable amount of time.

A company that is trustworthy is also essential. Often times the work will be performed when you are not there. You need to know the electrician will finish the job without you looking over his or her shoulder.

If you are ready to hire an electrician, you can count on The Electric Connection to meet and exceed all these expectations.

The energy saving power of lighting has quickly grown over the years, and still is to this day. In the commercial and industrial lighting space, a lot of companies are making the switch over from older technology lighting fixtures like metal halide and other HID lights over to LED fixtures.

On top of the energy savings LED can bring over older types of lights, commercial dimmers can yield even great energy reduction and thus a greater reduction in your facilities utility bills month to month.

So what is a dimmer, do dimmers save energy, and should I use a dimmer switch? Let’s find out!

A dimmer switch for LED lights gives you the control through a simple panel to change the amount of light that a lighting fixture (or fixtures) produces. You can dim lights as low as you so desire or as high as your light was designed to allow.

By having a commercial dimmer switch at your disposal, you can change the lights to match the mood, atmosphere, or even time of day to your needs and facilities guidelines.

Now onto the question you’ve all been waiting for, do commercial dimmer switches save energy?

The short answer is yes, dimmer switches do save you energy. But let’s discuss the history of dimmer switches and how far they have came.

Back in the day LED dimmer switches did not reduce energy because of the way they worked. Instead of reducing the amount of energy being used, they simply converted the energy not being used into heat instead of full illumination capability of the light bulb. Nowadays, dimmer switches for LED lights work by actually reducing energy used and only uses enough energy that it needs to power the light bulb at the setting of your dimmer.

Some of today’s dimmer switches use something called a “Triac Switch.” This Triac Switch works by cutting off power to the light fixture up to 120 times (variable) per second. Thus, the human eyes cannot detect a flickering and just see’s a constant flow of light. But while triac switches are used for smaller bulbs, bigger lighting fixtures use something called a send us a message and we will for sure help you out with that decision!