There are plenty of reasons to install new indoor light fixtures in your home. Perhaps you want to update your interior aesthetic, or save energy by upgrading to efficient LED bulbs. Maybe you even want to bring your lighting into a smart home control system. Although wiring a new fixture is usually a simple job, complications can crop up if your home still uses an outdated wiring system. In order to comply with your local building code, you may have to perform some extra electrical work to ensure the safety of your new fixture. Read on to learn more.

Bringing Older Electrical Work Up to Code

If your home still uses knob-and-tube wiring, the law prohibits connecting new light fixtures to the old wiring. You don't have to replace the entire wiring system itself, although that’s not a bad idea, because it can reduce your risk of an electrical fire and lower your insurance rates. Even if you don't have the time or money for such extensive electrical work, though, you can remain in compliance with your local code by installing an electrical box between your wiring and the light fixture.

You can purchase an appropriate electrical box at most local hardware stores – but make sure you verify that it is designed to meet local code guidelines for installing new light fixtures. From there, after you turn off the power to the room, you have to cut a hole in the wall where you want the fixture to go, large enough for the box to fit. If you're lucky, the fixture will be near a stud or part of the frame so you can mount the box easily. Otherwise, you have to cut the wall extremely carefully to ensure you leave enough lath and plaster keys to support the box.

Wiring the New Light into Place

Next, once the box is ready to be installed, follow the manufacturer instructions to clamp in the home wiring to the back of the unit. You may have to add a ground wire as well, depending on the specific scenario. Anchor the box using metal supports, and when it's all in place, connect the light fixture. When everything is securely connected, you can turn the power back on and give your new light a trial run.

Remember, knob-and-tube wiring can be a fire hazard, and performing electrical work in general can be dangerous if you don't know what you're doing. If you have any doubts or questions about installing your new light fixture, the best route is to have a professional electrician give you a hand.

Expert Assistance with Your Electrical Work

For assistance with all your electrical work, including installing new light fixtures, contact a qualified residential electrician today.

pursue electric lights.

A Timeless StyleIn the post-Victorian era, brass chandeliers shimmered with crystal drops and porcelain lamps were embellished with colorful floral themes. For members of the British aristocracy, the early 20th century was a time of elegance, luxury and opulence.

A quick glance through the latest designer catalogs are ample evidence that the decor of previous eras are still hugely popular. The style can easily be recreated with antique brass desk lamps. In contemporary homes, an elegantly crafted modern light fixture can give you the look of the most treasured antique.

picture light would also do the trick.

There are two things that regulate the power circuits in your home: fuses and breakers. Breakers are designed to turn off when they are using too much power, as that will prevent the wiring in your home from burning out. Fuses serve much the same role, though they don’t trip — they simply burn out when they are overloaded. Knowing how to replace fuses and breakers is important, as it will help you to keep the power in your home on at all times.

See, quick and easy to replace both fuse and breakers! If you need an electrician in Austin to come out and help you repair electricity problems in your home, call Bryant Electric Service today at 512-402-8587. One of our friendly service members will answer any questions you may have!

Smoke detectors are an important part of safety in the home. These cheap little devices can save your home and your life. If your lucky, the only time you’ve heard one go off is when the toast burnt. It’s easy for us to forget to check on them or even forget to test them after purchasing a new home. But they should not only be checked regularly, but require correct installation. Let’s go over some of the basics of having smoke detectors in the home.

Having smoke detectors placed in various locations around your home allows for fast and effective detection. Once the smoke detector siren sounds, it will warn you that there is a potential fire. You can quickly check the nature of the problem and hopefully prevent any further damage. It will also wake you at night before any harm can come to anyone in your home. The siren also helps firefighters quickly locate the fire in the home so they can focus their efforts.

Because smoke rises, smoke detectors are always placed on the roof for ideal detection. There are two common types of smoke detectors, photoelectric and ionization. Photoelectric sensors use a beam of light within the detector to sense any smoke in the air. The beam will shoot in a straight line when the air is clear. In the presence of smoke the light will scatter, this is when the alarm will go off. Ionization detectors use a chamber with a small electrical current. When smoke enters the chamber and the level of ions in the air changes, the electrical current drops and the alarm will sound.

It is recommended that there are smoke detectors on each floor of your home. If doors to rooms are closed often, it is best to have a detector installed in that room. The device should be placed away from rooms that create steam, such as showers or a laundry room, as this steam could trigger the smoke detector. Most smoke detectors use double sided tape to stick the device to the ceiling. You will need to drill the mount to your ceiling and attach the smoke detector to the sticky mount. Ensure that the batteries you use are working properly.

Smoke detector testing should be done on a monthly basis because batteries can die and sensors can become faulty. Each smoke detector will have a button on it to manually sound the siren. Push this button for a few seconds to ensure the siren is working correctly and the batteries are still active. To test the sensor, you can use an aerosol can of smoke to spray into the smoke detector. It may take a couple minutes for the siren to deactivate, as the smoke needs to clear from inside of the chamber first.

Smoke detectors are vitally important to keeping your home and family safe. We can help you to install smoke detectors around your home and position them to give you the best coverage.