If you’re considering the purchase of an electric car, good for you! You're doing your part to reduce the nation's reliance on oil and cut down on fossil fuel emissions, and you get to drive around in style to boot. But with many newer models, you’ll need to set up a charging station in your own home garage. Public charging stations are not widely available, and nothing beats the convenience of having a power source right outside your door. With an electrician's help, you can install a charging station on your property and get your car up to speed quickly. Read on for some tips on how to get started.

Expand Your Range

New, affordable electric cars (those that cost around $30,000) top out at ranges between 60 and 90 miles before they need to be recharged. That doesn't do you much good for a cross-country road trip, but it should be more than enough for the average daily commute. If you can plug it in overnight, you should be good to go the next day.

Technically speaking, the charger for an electric vehicle is found in the car itself, and the box you install to provide the electricity is called the Electric Vehicle Service Equipment (EVSE). The EVSE puts out 240-volt alternating current, and the charger in the car converts it to direct current to replenish the battery. Note that you can plug into a standard 110 volt outlet for some cars, but it will take 18 hours or more to fully charge them, making it impractical for daily use.

Pick Your Charging Spot

An EVSE can cost anywhere from $500 to $1000 or more, depending on what model you need, plus installation fees. More expensive models have higher amp ratings and can charge the car faster, generally speaking – some can get you ready to go in as little as three hours. The box needs to be placed within 15-25 feet of where you park your car so you can reach it with the charging cable.

Before you start the installation process, have an electrician evaluate the state of your wiring and circuit box – some older homes may not be able to handle charging a car without a significant electrical system upgrade. If everything checks out, the electrician can hardwire the EVSE or, alternatively, install a 240 volt outlet, similar to what you use for an electric oven or clothes dryer. The second option gives you more flexibility to move your charging station in the future, although outdoor installations usually require hardwiring.

The Code of an Electrician

To read up on the specific rules about how the EVSE needs to be installed, check out National Electrical Code Article 625 – your local building code likely has the same or similar regulations. For more help evaluating the suitability of your home for an electric car charging station, contact a local electrician today.

When discussing green energy solutions for the wind, a lot of people get nervous. People say wind turbines are unsightly or dangerous to wildlife. These people don’t realize that civilizations have been using wind power for a very long time.

As an alternative energy source, wind turbines produce a lot of energy and produce very little pollution. They are often are placed on hilltops or offshore. The winds offshore tend to be stronger and more consistent. In order to get the best unobstructed wind, feilds of turbines are usually built far enough offshore that they can’t be seen from the beach.

To understand the green energy solutions provided by the wind, you must first understand how they work. Wind is created by the sun heating the surface of the planet unevenly. With one side of the planet in darkness and the other in daylight, one is hotter than the other. Different air temperatures have different density. When hot air rises over cold air, wind is created. In any attempt to produce power, something is generated to move a turbine around. Common methods to accomplish this include running water or steam from burning coal. These methods are harmful to the environment, as they heat the water to unsafe temperatures or release toxins into the air. A wind turbine is a system that captures the kinetic energy of the wind to turn the turbine. Kinetic energy is energy caused by motion. When the turbine blades rotate, that motion causes a drive train inside the turbine to turn. A generator attached to the drive train captures the energy produced, and power lines whisk that power away to the consumer. There is no steam, no pollutants, and no dangerously hot water, only pure, green energy solutions.

The idea of the windmill dates back to the 7th century. In Persia, windmills were first used to turn the heavy mill wheels needed to crush grain into flour. They were mainly used for this purpose until 1887, when the first turbine was created to charge batteries in rural Scotland. The idea caught on fast, and by 1900, there were over 2500 windmills in Denmark. The Danes used the power of the wind to keep back the power of the sea, creating pumps for flooded areas. By the 1930s, many American farms used personal systems for battery charging, but it wasn’t until 1951 that one was finally connected to the power grid in the UK.

Modern turbines haven’t changed much from their original concept. They are made of modern materials and created on larger scales to capture energy more efficiently. One modern adaptation has been the ability to link several turbines together. This allows their energy to be combined and processed by a single substation, letting less power go to waste than if each were wired separately.

One of the reasons that boilers continue to stay popular as a method for home heating is that they can last for many years without needing major repair work, and their lifespans are longer than most other home heating systems. A well-cared for boiler can keep a whole generation of people in a home cozy.

FB Electrical Services offers boiler maintenance in Somerville, MA. Whatever services you need to keep your boiler working for you, you can trust to our talented team to provide it for you. We offer 24-hour emergency service for your convenience and peace of mind.