There are always things you need to buy. Sometimes life likes to throw little emergencies your way and you will be short on funds. Wouldn’t it be nice to find ways to save money on your monthly bills so you were prepared for those little emergencies? You may have noticed your electric bill going up. This is something you can expect to continue happening for the months and years to come. That electric bill is going to cut into your budget and make things a little tighter. Your Glendale electrician has some tips to help you lower your electric bill and keep a little extra money in your pocket. The team at The Electric Connection is here to help.

Replacing Light Bulbs

If you haven’t done it yet, you need to get rid of those old bulbs that are sucking electricity and running up your bill. Replace those bulbs with CFLs or have an electrician in Glendale install LED fixtures. CFLs use about 75 percent less electricity than incandescent and LEDs use about 90 percent less.

Use Less Hot Water

Shave a few minutes off of your daily shower. When washing your hands, rinse and shut off the water while you are lathering up and scrubbing. Turn on the water and then shut off again. Only wash full loads of dishes and consider turning the setting on your clothes washer to warm or cold water.

Unplug Appliances

It may not seem like a big deal, but every single thing that you have plugged in is drawing electricity explains an electrician. Glendale residents can save a few dollars every day by unplugging cell phone chargers, laptop chargers and even gaming systems that they don’t use regularly. Anything that is plugged in is drawing a small current. It is something known as phantom electricity.

These three things are easy and will not change your lifestyle in anyway, but they will save you money. If you have questions about energy savings or want to install energy-efficient light fixtures, give The Electric Connection a call today.

Other parts of the country may be warming up and getting ready to use our air conditioners, but we’re still relying on our heaters to get us through more than a few chilly nights. So if yours begins to malfunction, you may start to panic. This is understandable, but know that if you’ve had your system maintained before the heating season began, it may likely not even be an issue with the system itself.

Instead, you may be in need of Newton, MA electrical wiring services for some component of your heater. Keep reading to learn more about how your heater can be impacted by electrical issues.

This applies to both electrical furnaces as well as boilers. Both of these systems use heating elements—a set of coils that burn hot as a current passes through them—in order to raise the temperature of the air (furnaces) or water (boilers).

Both of these systems contain more than one heating element. Therefore, if you one fails you likely won’t lose your heat entirely, but your heater won’t be able to work as efficiently as it otherwise would.

If you’re utilizing a heat pump, then this is the most common electrical problem you might run into. Capacitors are cylindrical devices about the size of a soda can, responsible for sending electrical charges to the motors to start and keep them running.

Capacitors can burn out after years of use, or suffer from wiring issues, causing the heat pump to “hard start” (draining power) or quit functioning all together. You’ll need a professional to replace the damaged electrical capacitors.

Even if you have a heater that runs off of natural gas, oil, propane, or geothermal power, it’s going to have an electrical thermostat controlling it. Thermostats with failing wiring will begin to malfunction, often incorrectly registering your home’s temperature or failing to accurately set the heater. If your heater is failing to reach its target temperature with no other signs of a problem, your thermostat wiring could certainly be to blame.

Winter is in full swing in Australia, which also means you’re likely spending much more time in your hot tub. If you don’t currently have a hot tub, and are considering getting one installed in the near future, there are certain aspects to consider before buying one.

We all are aware that water and electricity just don’t mix; and so, sticking to the appropriate electrical and safety protocol with hot tub installations and their maintenance is something you can’t afford to overlook. Here are a few hot tub electrical requirements and safety tips to follow:

Even if you are a DIY enthusiast, installing a new hot tub is a completely different animal. Wiring of hot tubs isn’t an easy task and is distinctly more complicated and involved than setting up some other standard home appliances. Consulting an experienced and licensed local electrician will often save you a significant amount of time, money, trouble or even a trip to a hospital.

An electrician will make sure the electrical wiring and fixtures required for the hot tub are installed well and that helps avoid costly mistakes like ones that can occur in skilled and licensed electrician will make sure that the installation and wiring is in line with the existing codes.

Before installing your hot tub, it’s vital to consider its location. Not only will you need room for the actual hot tub but extra room to get into and out of it. The feature should be at least 10′ away from any type of overhead power lines and a minimum of 5′ away from removed spa panels. It’s also necessary to consider how the hot tub will connect to the power source.

Picking the right electrical equipment is essential no matter what line of business you’re in, so take your time with the selection process. It is especially crucial for companies in the food processing industry to pick the right cord grip and connector materials, since machinery and fittings at these plants are often exposed to harsh chemicals, water and other environmental threats, which can lead to corrosion, leakage and damage.

Electrical connectors for food processing plants normally feature corrosion-resistant properties, with different degrees of resistance for various environments and applications. Picking the wrong material will not just cause your connectors to require more frequent maintenance or repairs, but can also lead to short circuits and other safety hazards.