Holiday lighting products have evolved into a much safer product over the years.  With the development of properly sized wires and fuses and LED lighting to reduce the consumption load and the heat the lamps produce, holiday lighting has never been more safe.  In the past people would take the old C style lamps and hook one string of lights into the other.  Often overloading one the strings or the weakest link.  This overload would often melt wires, create sparks, and in some cases even cause a fire.  The manufactures and improved safety standards and testing, help reduce to the chance of an overload by installing a fuse at the starter end or male end of the light string.  This fuse would blow or trip when the load became greater than the fuse capacity, which would then project the wire from the overload.  It is always recommended to install lights that are interconnected (one light string plugged into the other) to manufacture specifications as listed by there instructions.

LED or light emitting diodes have not only made holiday lighting more efficient but even safer.  The old style C7 and C9 lamps could reach temperatures of up to 350 degrees.  The hot lamp if rested against wood or dry Christmas tree, has the potential to ignite the material from the heat the lamp produces and cause a fire.  With LED’s to replace the old style incandescent lamps the chance of fire from heat is almost non existing.  However, it is still possible to cause a fire from electrical spark or short.  These sparks or shorts produce heat much greater and can easily ignite flammable material.  Sparks or shorts are often caused by frayed or damaged insulation on the electrical wires and also loose connections.  It is important to inspect your holiday lighting for damaged or loose components and replace when needed.  Be sure not to use any damaged equipment and immediately discard them to eliminate the chance of future use.

A common mistake made people make with holiday lighting is to plug to many holiday lights into each other.  UL listed holiday lighting and cord splitters are tested to specific tolerances and should only be installed to manufactures specifications.  The easiest location to find the manufactures is specifications is to look at the tag on the cord most commonly found near the male end of the cord or light string.

If enough standard wall sockets are not present and you must plug in multiple cords, it is highly recommended to install a plug switch with a built in overload device to reduce the risk of overload.  The built in overload should not be mistaken for a surge protection device.  A surge protector reduces or eliminates the excess voltage going to the device plugged into itself.  Where an overload device will shut off power at the point of installation if to much power is being drawn through it.

On many new homes we will install plug ins located in the soffit or eve to reduce or eliminate drop cords for holiday lighting.  These soffit plugs are installed on a special heavier 20 amp circuit and often include a convenience switch located inside the home to shut the lights on / off as needed.  The special circuit makes sure your holiday lighting is not installed on regular interior circuits so the chance of variable loads and overloads are dramatically reduced.

Permanent holiday lighting can be installed by a licensed electrician.  The most common type of permanent holiday lighting is LED strip lighting.  These are can be installed on the under side of eves or soffits for a permanent installation.  Depending on the type of LED holiday lighting you choose you may even have the option to change the colors of the lights with a push of a button.  This allows the holiday lighting to be used for many occasions throughout the year.  You can call today or schedule online to have a lighting specialist come to your home or business and provide you with a written no obligation quote.

via Wikimedia

2. Ricky Martin wins Song of the Year

Puerto-Rican heart throb Ricky Martin played a huge role in bringing Latin pop to the American music scene during the 41st Grammy Awards show in February of 1999. In December he was rewarded again at the Billboard Music Awards by winning Song of the Year for his hit single “Livin’ La Vida Loca.”

The London Olympics are certainly on the tip of nearly everyone’s tongue (and Courtesy of FrenchArt-Deco.com

This piece, entitled “Swimming Pool” by French artist Albert Decaris won gold in the Engravings and Etchings competition.

In 1949, the International Olympic Committee decided to stop all art competitions, reasoning that it was illogical to let professional artists compete, while only amateur athletes were eligible. Instead, cultural festivals replaced the art competitions, and still do to this day. There’s still a chance for the best of the best artists and entertainers to showcase their stuff on an international stage, and for lighting designers, this is certainly a world class exhibition. 

LED is the light source that’s in it to win it this summer, wowing Olympic fans with spectacular light shows and festive monuments alike.

At the opening ceremony, LEDs were at the center of almost everything. The dove bikes used LEDs to light up their wings as they performed a circuit of the stadium.

LEDs lit the screen showing the Queen’s acting debut, with none other than James Bond.

Even on the sidewalk outside the main Olympic Stadium, there are 20 circular slabs that capture the kinetic energy of pedestrians’ footsteps to light up nearby LED lamps for 30 seconds at a time!