Let’s face it—halogen and incandescent headlight bulbs are a thing of the past. fanless, driverless LED headlight bulbs were used in this installation.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points. Repeat these tape lines for your other headlight.

6. Remove your headlight assembly if necessary, remove the current bulbs, and install your new LED bulbs. Check your owner’s manual for specific instructions on how to replace your headlight bulbs.

7. Depending on your vehicle, you may have to adjust your headlight beam before or after the assembly has been reinstalled. Your owner’s manual will explain how to adjust the beams. Align each headlight so that the top edge of the beam is at the same height as your horizontal line(s). If your headlights can be adjusted horizontally or produce two light cutoff points, use the vertical tape lines to align them properly.

3. Shake the vehicle to ensure that your suspension system is settled. For more precise adjustments, inflate all tires to their designated psi capacity and have someone sit in the driver’s seat. Also, make sure that your vehicle’s gas tank is at least half full.

4. Measure from the ground to the center of your headlight assembly where the bulb is located. This step must be done for all vehicles. If your vehicle allows for horizontal headlight adjustments in addition to vertical adjustments, it’s important that you also measure the distance between the centers of both headlight bulbs. The vehicle featured in this video allows for vertical headlight adjustments only; therefore, center lines aren’t necessary but are shown for demonstration purposes.

5. Turn on your low-beam headlights. Using painter’s tape, mark your headlight measurements on a flat wall. Measure from the ground up, and apply a horizontal line of tape to the wall; this line represents the top of your headlight beam. You can either apply one long, continuous line or small sections where the brightest areas of the headlight beams are shown.

If your vehicle allows for horizontal adjustments, mark the distance between your headlight centers with two vertical lines of tape. These lines are important for projector headlights and/or lining up beam cutoff points.

You never know when things are going to go haywire and sometimes you just don’t have an idea what to do next. A light that is flickering could be a bad bulb or it could be faulty wiring. An outlet that is working one day and then dead the next is perplexing as well. You may not even realize you have an electrical issue. So how do you know when you need an electrician in Glendale? The team at The Electric Connection has a few tips for you to follow when things are not quite right.

*A flickering light that is not remedied by replacing the bulb with a fresh one is a reason for a call to your electrician. There could be some faulty wiring or wiring that has frayed or been damaged by rodents. If it is not taken care of, it can result in an electrical fire.

*An outlet that works sporadically is also cause for alarm. It definitely indicates there is some trouble with the wiring. It is best to get it looked at right away.

*An outlet that has black streaks shooting up the wall or arcs blue when you plug something is a definite sign of trouble. Avoid using the outlet until you can have it checked out. Glendale electrical problems are serious. Fortunately, these early warning signs give you a heads up that your home has an electrical problem that could end up starting a fire.

*If you smell burning wires, get out of the house and quickly call an electrician. This is an emergency that should not be put off until tomorrow. If you have any other questions or concerns, give The Electric Connection a call today. You can schedule and electrical safety inspection to help set your mind at ease while identifying any potential problems.

When you flick on the light switch, what happens? If you’re thinking “the room lights up… hopefully,” then you’re probably missing out on an opportunity for breathtaking lighting to do so much more than just let you see in the dark.

Your home should look intentional and deliberate, not just functional. Lighting is one of the best, easiest, and most easily ignored ways to make your home go from “nice place,” to “oh wow.” Seriously! Think back to the first time you saw under-cabinet lighting, for instance. Wow, talk about a way to get the most out of a space, while still showing off the best aspects out of the kitchen. That is exactly the effect that an inspired electrician can create, simply by optimizing your layout to handle some really nifty things with lighting. Even if you don’t decide to pull the trigger on the uplighting for your soon-to-come artwork, having the ability to add that in with little effort later thanks to a box hidden in the wall (just in case) takes almost no effort on our part, but can make a tremendous difference in your home’s perception, and value, down the road.

Light doesn’t just shine from one direction. Even sunlight is seen in the form of reflection, direct contact, and general ambient lighting. These simple principles are the same that should be used and recreated in your home. Your home should mirror that breathtaking view you saw on your favorite vacation, when the sunlight shone just so; conjure up that image, then imagine the architecture of your home and how it could be better illuminated. If you’re drawing a blank, don’t worry, that’s what our experienced electricians are here for. We’ll happily handle the up lighting, room lighting, and ambient lighting to create the effect that you’re looking for, even if you don’t really know how to explain it or where the circuits need to run. While all of this sounds expensive, creating a couple of extra lighting lines is simple when you’re already committing to work on your home, but becomes much more difficult later; always take advantage of the opportunity to bring an electrician and find out what is possible – 9 times out of 10, we find that homeowners who do this thank themselves for it later.

One of the biggest mistakes that builders and general contractors make is doing the bare minimum for lighting, leaving the home with nothing but a few can lights either dimly lighting the room or blinding everyone inside. Don’t let your lights let you down, or you’ll find that all your painting and furniture efforts just seem to fall flat of that wow factor you’re looking for.

Contact Electrical Gurus in Des Moines for the inspired, experienced service you need to create artistically inspired lighting for your home. When done right, you’ll find an incredible amount of value in a couple of lighting changes.

By Clarissa Allison | December 11th, 2015

If you are lucky enough to have a large family room or “great room”, you may encounter some exciting challenges when choosing home decor and lighting that complements and balances your space. A great room is a large room typically found in modern homes that combines the features of a living room with those of a dining room or family room.

Large, open spaces are very common to find in floorplans these days. The dining room incorporates the kitchen, which is part of the living room and leads into the den, etc.  This trend sees walls to separate activity spaces removed. You’ll find that the kitchen is no longer segregated from the rest of the home but may easily become a main focal point. As you’ll see, the key to lighting these types of spaces is variety. You’ll want to utilize ambient, task, wall, and spot lighting to eliminate a “cave-like” atmosphere and maintain a feeling of spaciousness and height.

Read on for tips on how to set up the perfect lighting scheme for functionality, elegance and entertaining.

Update Your Kitchen Island As An Activity Space