Recently, Digital Trends profiled a Paolo di Trapani, and his work has a lot of people excited. For all the rapid progress that has been made with LEDs, no one else has made this important step towards recreating natural light.

The article explains how lighting innovations have allowed people to use artificial light in a number of amazing ways. We can change the color temperature of a light bulb with a smartphone, and we can grow food indoors, but we haven’t yet been able to mimic the way the atmosphere scatters the sun’s natural light…until now.

According to Digital Trends, di Trapani’s technology scatters the light of a panel of white LEDs with “a clear plastic panel studded with nanoparticles that are invisible to the naked eye.” What’s a nanopartical? A nanoparticle is what it sounds like: A really small particle. Nanoparticle research is currently hot because there are tons of ways that nanoparticle research could be applied in biomedical, optical, and electronic fields.

Gas prices are fabulous—right now. We all know it is only a matter of time before the gas prices creep back up and we will once again be forced to pull from other areas of our monthly budget to afford to drive our vehicles. Many people have already made the switch to electric cars in an attempt to save money on their gas bills while reducing the strain on natural resources. There are plenty of different models of electric cars available that are sure to suit your needs. When you make an electric car purchase, you will likely also buy a charging station for you car. An electrician in Pasadena has some vital information for you. The team at The Electric Connection can also help answer questions about the electrical requirements of your electric car charging station.

When you buy your car, you will have the choice to buy a Level I or a Level II charging station. A Level I station is essentially a trickle charger. It sends a small charge to your car and can take upwards of 24 hours to fully charge the car. This charging station can be plugged into a standard outlet. However, it will need to be the only item plugged into that outlet and should be on its own breaker. If you need additional outlets or breakers, your electrician can take care of that for you.

A Level II charger is a fast charging system that typically fully charges a car in about 8 hours. This charging station requires a 240-volt outlet, which is not standard in your garage. It is a special outlet that will require installation by an electrician experienced with Pasadena electrical requirements. An inspection of your breaker panel will need to be conducted to make sure you have room for an additional breaker dedicated to your fast charging station. These are all things your electrician will evaluate on the first call. Give The Electric Connection a call today and schedule your consultation.

If you’re in the midst of a renovation or simply rearranging your floor plan, then you’ve likely come across the need to add or relocate a light fixture. Maybe your new dining room table is a little wider than the old one, you’re adding a kitchen island with pendant lights, or you’ve finally convinced your significant other to let you get that pool table you’ve always wanted. In any case, you need to move or add a light fixture – but how and when?

First, it should be noted that, contrary to how it may seem, most light fixtures are not connected to a joist or even drilled into wood. Instead, hanging light fixtures and ceiling lights alike are located between joists and supported by electrical boxes that grip a wide surface area of the sheetrock that makes up your ceiling to support the weight of the fixture below; for heavier fixtures, like large chandeliers or ceiling fans, there are larger, even joist-secured boxes that will need to be used.

If you’re moving a light fixture, it is important to note that there are certain limitations as to where the fixture itself can go. If you wish to relocate the fixture to a place where a joist exists just above, then you’re likely going to have to use a swag hook and chain to anchor the fixture in place, as a box under a joist is not an option. That said, if you’re moving the housing for the fixture itself, you’ll need to know which direction the joists above run, then choose to move it either through the same joist cavity or drill through a joist to run the current wiring to the new housing. Other things to consider include which switch controls the light and where it is located, as it is a safe bet that a wire will have already crossed all joists above (at some point). This can prevent your electrician from drilling needlessly by allowing them to fish the wire back to the earlier point. If your switch is further away than the destination, you can bet they’ll have to do some drilling. Jumping through, between, and around the joists in the ceiling represents the largest obstacle your electrician (and light fixture) will face.

Once your location is set, all that is left is to get your electrician out to assess and perform the work for moving your box. If you’re planning on doing one large fixture over a pool table, island, or entire room, then you’ll want to take into account the power output of the fixture compared to what that circuit can safely allow for as well as the weight of the fixture. A typical rule of thumb is that anything under about 35 pounds can be handled by a standard drywall box, but something more (or with a fan) will need extra stabilization. Surprisingly, if you’re running numerous small pendant lights, the electrician may have an even easier time running the circuit and ensuring that your lights are up and running in no time. Just be sure to discuss the fixtures you have in mind with your electrician before you purchase them to know what they believe your limitations are!

Whenever you need electrical work done around your Des Moines home, contact the experienced professionals at Electrical Gurus. We are proud to offer the finest licensed local electricians in the area and are always more than happy to help out on your household projects.