The answer to the question above is a bit tricky. First things first, not every homeowner is necessarily going to require air duct cleaning services. However, should your air ducts require cleaning, it is always necessary to schedule that service with a trained and properly equipped technician. After all, there is really no way in which on can hope to access and thoroughly clean their air ducts on their own. The hidden nature of ductwork can make assessing its interior condition rather difficult, though. That is why we have compiled a few tips for helping you to identify the need for air duct cleaning services in Boston, MA. Contact FB Electrical Services to schedule exceptional duct cleaning service today.

Cities like Colorado Springs, Denver, and Pueblo are constantly expanding and urbanizing—you can always spot a new neighborhood development on your commute to work. New homes are sprouting up all the time, and people are buying. However, sometimes new isn’t always better (or cheaper). There are a lot of great, older homes throughout Colorado cities, and are often a better choice when it comes to real-estate investments. If you currently own an older home, or you are considering purchasing an older home, you’re going to want to check for these common electrical problems that could cause issues in the future in terms of both safety and money.

Generally, homes that were built after 1940 are in the clear—they are usually safe and the electrical systems were installed up to code. Homes built prior to the 1940s should be evaluated, however, as many of the electrical wiring could have deteriorated or may not be able to power a home in this era of modern day technology and appliances. Regardless of when your home was built, it might be a good idea to have an electrician come out and evaluate the wiring systems in your home and ensure that your family will be safe. Here are some things that you can look for yourself when it comes to old wiring in old homes:

Old Cables

Metal cased, fabric covered, or frayed wires are signs that your wiring is outdated and unsafe. Many times during the early 1900s, electrical wiring was “protected” by metal jackets or canvas-like cloth, which can cause problems if the insulation in your walls has been damaged or aged, or even if the metal electrical cords were placed on inadequate grounding. If the wires get exposed, or start to fray in these two locations (next to insulation or on top of a poor electrical foundation) this could be a serious fire hazard waiting to happen. You know you need to call an electrician and get your wiring replaced when you can see any scorch marks on switches or outlets, when you see torn, damaged, or missing insulation, or when you see exposed wires that could potentially cause a fire.

ZINSCO and FPE Panels

Zinsco Panels

While popular around the 1970s, Zinsco panels are almost obsolete today. However, older homes can still have these panels as a part of their home’s electrical system. Not every Zinsco panel needs to get replaced, but it would still be a good idea to get it inspected, as these panels have circuit breakers that have been known to melt into the main bus bar and cause a fire.

FPE Panels

Federal Pacific Electric panels were distributed throughout thousands of homes in the 1950s to the 1980s, and have an unfortunate reputation of being extremely hazardous to the safety of you and your home. These panels have been known for their inability to trip the circuit breaker when the circuit is overloaded or short. When the breaker doesn’t trip, it instantly puts your home at a fire risk because the circuit is taking on much more than it can handle and has no way to shut itself off.

If you recognize either two of these logos on your electric panels in your home, call an electrician immediately to get them inspected.

Old Fuse Boxes—Below 100 Amps of Power

Houses built before the late 1940s and early 1950s were not expected to handle the amount of electricity that we use in modern time. That being said, the homes were installed with a circuit box that can only power 60 amp service (four fuses), or sometimes even 30 amp service (two fuses). This means that your older home may not be able to power all of the appliances and electronics that you have in your house. If your breaker is tripping constantly, or your electric bill is through the roof, this may be a sign that your older home needs an electrical inspection to update the amp-service. Older electrical panels are also at risk of starting a fire. If you are unsure whether or not your home is experiencing this, call an electrician to be safe, and they will be able to give their expert opinion on whether or not you need to upgrade your electrical panel in your older house.

These are just a few signals of outdated electrical work in an older home, but each one is a serious risk to the safety of you and your family. If you have an older house, be sure to get it checked out and evaluated for safety. The same goes for those who are looking to buy an older home in the Colorado area, as the electrical work could be outdated and dangerous.

Whether you’re doing industrial wiring or residential wiring for electricity, you’ve got a complex task ahead of you. Needless to say, industrial wiring is essentially a much more complex form of residential wiring. This article will assume that you have some elemental electrical wiring knowledge or aptitude, and it will simply provide you with a very basic overview of what you need to understand with regard to residential wiring and industrial wiring.

It will be up to you to look up your local building and electrical codes for your home or office space. Also, check your local laws to see if you are even permitted to do your own amateur wiring before you proceed. Above all things, approach any wiring project with this knowledge at the forefront of your mind: “electricity can be deadly.” Put your safety ahead of all other concerns.

Red wires and black wires are usually “hot”. This means that there is a current (amps) flowing from the circuit breaker to the electrical box or the appliance in question.

The white wires usually are “returns”. This means that they allow current (amps) to flow back to the circuit breaker after the electricity has passed through the load or appliance in question.

White wires should not be connected together with ground wires, with the exception being back at the circuit panel bus bar. If you fail to observe this rule, then every single time the load is energized (such as turning on an appliance), electricity will flow through the ground wire and the return wire simultaneously. This is very dangerous.

A ground wire is usually bare and attaches to an appliance’s frame. Under normal circumstances, current should not be passing through it. Only when there is a short circuit should electricity pass through the ground wire; this happens so that the circuit breaker will kill the flow of current to the site or appliance.

Smart industrial wiring is based on 3-phase electrical power. 3-phase electric allows less workload to be placed on each wire involved while at once allowing them to work together to give you maximum results. With 3-phase electric, the wires are smaller and the motor is smaller than a typical single-phase motor. These factors allow greater efficiency and longer lasting motors and wires.

There are four types of 3-phase electrical power:

No matter which type of 3-phase electrical power you choose to use, you’ll need a voltage meter in order to determine the actual voltages that are available to you. The type does not determine this.

Industrial wiring typically runs through metal conduits, armored cable, or a raceway. These enclosures are the safety ground–never the neutral wire.

The above information should give you a nice guidepost for doing more research into and getting more practice with either residential wiring or industrial wiring. Again, safety comes first!

We all know or at least heard that converting from Metal Halide (High Intensity Discharge) to LED will save you money.

But how much? Are there any other reasons or difference you should know about?

In this article, we break down all the factors that you should be aware of before making a decision to convert from Metal Halide to LED. Here are the 9 reasons we think LED wins over Metal Halide.

Let’s take a look at the information on a typical 400 watt metal halide bulb. While specifications may vary, a visit to a popular online website that sells Metal Halide bulbs shows that a brand new bulb has the following specifications:

We have just as many customers wanting to convert to LED because of maintenance savings as they do for energy savings. Think about what we discussed, over the life of the LED retrofit kit, a customer would have to do 5-6 Metal Halide replacements. The higher the installation height, the higher the cost of replacement. And if you have a facility loaded with lights, this becomes a significant budget amount every year that you must take into consideration. Now, we know that reduced maintenance time on lights does not translate into dollars saved because it is highly unlikely that people will lose their jobs over the fact there is much less work to do. However, these people will have time to now work on things that matter, like fixing the machines that make the company money instead on replacing lights that cost the company money.

When you take a measurement of light with a light meter, it reads lumens. And this measurement of all the lights that contribute to the light at that location creates a measurement called foot candles. But let’s think about that light that is being measured. Metal Halide creates all sorts of light, in all spectrum’s, visible or otherwise. This includes UV and IR spectrum’s, visible to the measuring device but not visible to the human eye. LED, on the other hand, does not produce UV and IR. Therefore, its readings using the same light meter is only picking up visible spectrum’s.

So there is a fun little test you can do. Have 2 light sources, LED and Metal Halide. And first ask, which one is brighter? And if the right LED source was selected, they should say LED. And then use a light meter, and the light meter may say the Metal Halide area is producing more foot candles. And so now you know part of the reason, but wait, there’s 2 other pieces of information you need to know.

Click here to see our infographic on Retrofitting vs Replacing.

Conclusion