RGB LED strip lights are a great way to add a pop of color to your above-ground pool. These low-voltage LED lights can be applied to the inside rim of your pool or around your pool deck. With RGB LED strip lights, you can choose from a ton of dynamic color-changing and single-color modes with adjustable brightness and speed control. They’re great for parties or late-night swims and can be easily installed. We’ve included installation instructions for our waterproof LED strip lights. Some cities require above-ground pool lighting to meet National Electrical Code (NEC) Article 680 standards, which would limit possible pool lighting installation locations. Before you purchase LED pool lights, check your city’s code requirements. We also recommend that you have a certified electrician install your lights.

1) Before ordering your LED strip lights, measure the diameter of your pool and multiply by 3.14 to find its circumference; this number indicates the total length of strip that you will need. The 21-foot pool used for these installation instructions has a circumference of 65.94 feet and requires 4 runs of 16-foot LED strips.

You will also need to measure the distance between where your power supply will be and both sides of your pool where the amplifiers will be installed (see the setup and wiring illustration below). These distances will tell you how much 18-gauge wire you’ll need for connecting the amplifiers to power. Make sure to account for the distance of any dips or turns that the wires may take along their paths.

Lastly, measure the approximate distance that will be between your controller and where your strip lights begin. This distance will tell you how much 22-gauge wire you’ll need for connecting the controller to your strips. You will also need two small sections of this wire for connecting your first and second strip lights to the amplifiers.

2) Before you’re ready to install your LED strip lights, be sure to drain your pool. Begin by creating or locating a dry area away from your pool for the power supply. The power supply should be contained in a weatherproof box. Power supplies should be installed between a ground fault circuit interrupter (GFCI) protected circuit and the pool’s junction box. It’s crucial to use a GFCI protected circuit as it shuts off if current flows where it’s not supposed to.

Wire the included plug to the power supply, but do not connect to power until the installation is complete.

3) Connect your RGB LED controller to the power supply. Cut the barrel off of the controller wiring. Strip back the remaining wires, and connect its wires to the power supply.

4) Cut the LC2 connector off of the remaining end of the controller, and strip back the wires. Run 22-gauge four-conductor wire to connect the controller to your low-voltage pool lights; use dolphin connectors to join like-colored wires. Connect your first two LED strip lights to the controller by joining each set of like-colored wire with a dolphin connector. You should be connecting four wires of each color (red, blue, green, and black) together. For added protection, cover all wire connections in this installation with electrical tape.

5) You will apply strip 1 clockwise around your pool rim and strip 2 counterclockwise. If you have a flat surface, use mounting clips to secure the strips in place as you go. If you want to mount the strips under your pool rim, drill small holes in the trusses approximately every 2 feet. Use cable ties to anchor the strip to the truss. You can also use speed nuts or cotter pins for strip anchoring to avoid drilling holes.

Solder a small section of 22-gauge four-conductor wire onto the strip’s end terminals. To reseal the LED pool light strip, slide wires through the holes of a 10-mm end cap, fill the cap with silicone, and slide it into place on the end of the strip. Be sure to cover all of the exposed conductive traces to ensure water resistance. Allow a minimum of two to three hours for the sealant to cure.

7) Once the new end wires are attached to the strip, you will mount the amplifier. Use the double-sided 3M foam pad to mount the amplifier in the middle of strip 1 and strip 3. For best results and added security, apply 3M adhesion promoter to the amplifier and its installation location on the pool wall.

8) Using a dolphin connector, join each like-colored wire on strip 1 to the same color on one end of the amplifier. Do the same when connecting strip 3 to the other side of the amplifier. You should be connecting three wires in each color (red, blue, and green) together on each side of the amplifier. The black strip wire will be joined with white amplifier wire. Note that the separate group of just black and red wires are meant to be connected to the power supply. Follow the same instructions for connecting strips 2 and 4 to the amplifier on the other side of the pool.

9) Use 18-gauge wire and dolphin connectors to connect the amplifiers to your power supply.

10) Plug the power supply’s attached cord into an outlet, and enjoy your LED pool lighting system! Refill your pool with water, but make sure to leave space between the water line and the lights.

For more LED pool lighting options, see our entire selection of waterproof color-changing LED strip lights.

For technical questions, don’t hesitate to call us toll free at 866-590-3533. Our customer service and technical support teams are available from 8:30 a.m. to 8 p.m. CDT Monday-Thursday and 8:30 a.m. to 4 p.m. CDT on Friday.

The ENERGY STAR® Partner of the Year Award. Sea Gull Lighting’s focus remains on delivering on-trend, high quality lighting products with unparalleled customer service and best-in-class availability. For almost 100 years, they have built strong relationships and earned a reputation among channel partners, builders, contractors and homeowners to be among the very best. Sea Gull Lighting looks forward to the evolving business landscape, and with its continued commitment to serve, and to listen and learn from its valued customers, is poised for success as it soon enters its second century of operation.

Are you still using incandescent light bulbs? Your electrician would recommend a different course. Efficient lighting technology has blown up in the last few years, and advanced technologies are just getting better. Light emitting diodes, or LEDs, are at the forefront of modern lighting thanks to their inexpensive and long-lasting luminescence. Some of these new diodes are leading the pack in must-have lighting features, including smart home integration that you can control with your phone. Read on to learn more about the latest in LED technology.

Upfront Costs are Dropping

One of the biggest complaints about early LEDs was the price. Almost any LED will save you money over time compared to an incandescent bulb, since they use 25 to 80 percent less electricity and can last up to 25 times as long, but many consumers balked at paying the $35 or higher retail price for a single bulb. Newer models, however, can recreate the look of that classic 60 watt incandescent bulb with fewer LED panels, meaning they are cheaper to produce and sell for $10 or less.

Options are Expanding

Other common complaints about the first LED models were that the warmth of the light wasn't quite right and they didn't work with accessories like dimmers. With today's technologies, however, you can find LEDs that give off almost any color and lighting profile, allowing you to mimic the look and feel of your old incandescent bulbs or tailor your room to fit more eclectic tastes. Not every LED is compatible with standard dimmers yet, but many are – just check the label on the box to make sure.

Make it a Smart Bulb

Many new LED models are designed specifically to work with smart technology. That means you can control them from your phone no matter where you are, set up a schedule for them to turn on and off, and even have different colors or light intensities at different times. Newer bulbs are also optimized to work with your other smart home systems to move you closer to a goal of integrated whole-house control.

Turnkey Functionality

One of the biggest advantages of upgrading to LEDs is how easy it is. There's no need to hire an electrician to set up new wiring or fixtures – the bulbs screw right into the pre-existing bases, out of the box. If you want tips on how to make the most of your new lighting options and create the room profile that fits your home, however, don't hesitate to call up your local electrician for guidance and advice.