As a homeowner, you might not be aware of all the features your home has, especially when it comes to your electrical system. It’s like another occupation trying to keep up with your home’s appliances and making sure everything works properly. One of the things, however, that is so important to take care of is your electrical system and the features that are involved or connected to it. Not only does it help to understand your electrical system and what it can do for you, but it will also help you become more efficient especially when you’re trying to save money on your utility bill. Keeping your family safe is also a necessity, so keep these electrical features in mind and know how to keep your home safe with your electrical system.

Once you understand your electrical system and know how it works, you’ll notice a host of beneficiaries. You’ll be increasing the safety of your home, especially when a small problem arises and you’ll know what to do in that place and time. Meanwhile, you will also know how to avoid any potential problems and end any lasting effects that can be damaging to your home. And on top of all these benefits, you will also decrease your monthly utility bills. What’s better than that? Knowing your electrical system allows you to understand what works efficiently and what doesn’t, which avoids the cost of wasted money in the long run. Lastly, you can make smarter energy consumption choices. You’ll be able to identify which habits work for you and your family and which ones are affecting your lifestyle and costing you more out of pocket expenses.

If you’re dying to install your new instructions for how to install a light bar. These instructions include options for installations with or without a wire harness and for connecting to existing LED lights. Installation will vary based on the type of vehicle, existing lighting setup, and chosen wiring method, but these instructions can serve to give you a general idea of the process. Light bar mounting instructions are also available and are listed by WH-DTS10, WWH-DTD30; (ATP) WH-ATPD20, sdoptional mounting brackets; be sure not to overtighten the hardware (you will need to adjust it in step 7).

3. Route the lighting side of the wiring harness from the battery to the light in a safe, secure manner. Connect the harness to the light. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wiring harness is a safe path to follow. Some lights may not have DT or ATP connections on them, but the connectors can be added from the harness kit or purchased separately (ATP-FPT).

4. Continue to route the switch portion of the harness to the desired location of the switch. The switch may need to be unplugged from the harness to make routing of the harness easier. An optional remote-controlled switch (RS-x) are also available with different legends.

5. Connect the black (ground) wire with the large ring terminal from the harness to the negative battery terminal. Connect the red (power) wire with the large ring terminal from the harness to the positive battery terminal.

6. Secure the relay to a suitable location, and test the light to make sure the circuit works.

7. Finally, aim the light in the desired direction, and tighten all mounting hardware.

3. Connect the black ground wire of the new light to the ground wire of the old light with solder and heat shrink tubing (PSC-x). Connect the red power wire of the new light to the power wire of the old light.

4. If the new LED work light or off-road light bar has an ATP or DT connector that you wish to utilize, corresponding ATP (DT-MPT) pigtails are available.

5. Finally, aim the lights in the proper direction, and tighten all mounting hardware.

1. Find a suitable mounting location that will allow for running wires and mounting the LED light bar. Mark where your holes will be for the light bar brackets or mounting feet. Check behind drilling locations to ensure nothing will be damaged. Drill appropriate-sized holes.

2. Mount the lights with the provided hardware or with DT-MPT or RRS-SP, RRS-SPx, or RCS-RF25A) under your hood to speed up install time and avoid routing wires through your vehicle’s firewall. Route another run of red wire from the pigtail adapter (connected to the light) to the output terminal of the switch. Be sure to avoid heat sources and any moving parts while running your wires. Prolonged chafing of the wires may lead to a short in the circuit. Typically, following the vehicle manufacturer’s wire harness is a safe path to follow.

4. Be sure to double-check for all obstructions and proper clearance. Drill an appropriate sized hole for the switch, and mount it.

5. Connect your black wire to the negative battery terminal. Connect your red wire to the switch input terminal and to the positive battery terminal with an appropriate-sized fuse holder (MAF-x) installed within 18 inches of the battery. You will have to cut your section of red wire to allow for the fuse holder to be installed between the switch and battery. Connect your other run of red wire to the switch output terminal.

6. Finally, aim the lights in the proper direction and tighten all mounting hardware.

If you’ve read our blog for any length of time, you know we’re pretty enthusiastic about light. At Pegasus Lighting, we love writing about lighting design, technology, news, advice, art, and more. BUT we also love to read about it. For today’s post, I decided it was high time to send a shout-out to some of our favorite lighting blogs, magazines, and websites. Each one is run by passionate individuals and offers a unique perspective on the lighting industry. And you better believe they keep us on our toes.

So without further ado…

To indulge your inner lighting geek, check out Lighting Science’s company blog. You’ll learn things like how lighting affects sea turtle behavior, what it can do to our sleeping patterns, and more. The best part – Lighting Science is actively solving these problems with new, creative lighting technology!

Here’s a bright post:

Lighting designer James Bedell shares his unique blend of expert knowledge, honest opinions, and passion for lighting on his personal blog, and it’s well worth a read. Some days he’ll share practical tips about how to light your home, while other days might be some fascinating insight about what we can learn from a sunrise.

Here’s a bright post: 

When you’re in the mood to look at something pretty, or cool, or crazy, it’s time to navigate over to Lightopia’s Light Public. The lighting enthusiasts on this blog post about commerical lighting design, fine art, and photography mostly – and it will blow your mind.

Here’s a bright post: