A common lighting technology in the commercial space is metal halide, at least in the past it was. At an ever increasing rate, businesses are actively searching for a more efficient lighting system that will allow them to cut energy consumption and in turn; reduce overhead expenses.

When companies or facility managers start their search, they often search for the wrong answer. Here are some common questions that we are asked:

“How many watts does it take to replace a 1000w metal halide light?”

“How can I replace my metal halide light?”

“Is it even possible to replace my metal halide fixture with another technology?”

This post specifically will be covering the first question, as for the other two: be sure to subscribe to our email list to know when new posts go live, we are always pushing out informational content to answer your questions just like these ones!

So.. How many watts does it take to replace a 1000 watt metal halide fixture?

It’s simple a simple concept, yet not at the same time. In short, it’s impossible to know just from that question alone. The reason for this is simple too: you can’t base your decisions off of watts alone. Instead, you need to be basing your decisions off of lumens.

What is a LED equivalent to a 1000w metal halide you can easily find fixtures that output at over 100+ lumens / watt. Especially when you go with quality products from reputable companies, you can reach higher than a 150 l/w output. This will allow you to cut your wattage usage per fixture by 2-3 and sometimes 4 times which will prove to save substantial amounts of energy when you start talking about replacing multiple fixtures.

So we’ve explained what it takes to replace your 1000w metal halide fixture, but what does “replacing” consist of?

Replacing can consist of two things: write in to one of our professionals with your questions.

A home power outage can happen without warning and at the most inconvenient time. Really, there isn’t a convenient time to lose electricity. We often forget just how much we rely on power throughout the day until we lose it.

The loss of lights, refrigerators, washers and dryers, computers and electronic devices, and more make residential power outages both irritating and disruptive– there are a number of steps you can take to fix the situation.

Diagnose the Problem

There are many reasons you may have lost power.

First, something may have caused an interruption of power from your provider.  In addition, Colorado thunderstorms can cause a disruption , or it could be a problem with a circuit or other electrical system in your home. Loose connectors, device failures, ground movement, underground root growth, or improper wire installation can all cause shorts or overloads as well.

If you have lost power, check with your neighbors to see if the power outage is widespread. If they don’t have power either, the problem is with your power provider, not the electrical systems in your home. Your power company should be informed, and you will have to wait for them to address the issue.

If the power outage is limited to your home, check your main breaker to see if it’s tripped. Flip the switch back on if it is tripped, which may restore your power. If you are only experiencing a partial power outage, you can try to turn on your electric dryer or range as a test. If it doesn’t turn on, or if the main switch trips again at any point, you will need a professional electrician to come and diagnose the specific problem you are having.

A Trusted Emergency Electrician in Arvada

If you were to go back in time and tell someone living in the 1960s that aluminum wiring replacement in Fairfax, VA is the best choice they can make, they may be a little confused. Fifty years ago, aluminum wiring was in. Copper spiked in price and many new homes built during that time were equipped with aluminum wiring under the belief that it was the more cost-efficient option. However, cost-efficiency did not equal safety, as homes with aluminum wiring proved more at risk for electrical fires. Speed up fifty years and in a 2016 world, aluminum wiring is now incredibly unsafe.

When you hear something a lot, you tend to brush it off. Warnings about changing the batteries in your smoke detector are heard so often, it is easy to push the advice to the bottom of your to do list. When the smoke detector beeps incessantly, it is easier to pull the battery out with the idea you will put a new one in tomorrow. All of these seemingly innocent plans can actually be extremely dangerous. You never know when a fire will break out in your home and often times, it happens when the batteries are out of the smoke detectors. A good option for every home is to have hard-wired smoke detectors installed by a Los Angeles electrician like those at The Electric Connection.

Hard-wired smoke detectors remove the risk of a fire going undetected by a smoke detector without batteries. The smoke detectors are wired directly into the home’s main power by an electrician. Los Angeles homeowners will take comfort in knowing that as long as the power is on, the smoke detectors are functioning. There is a place to batteries in the detectors to act as a backup system should there be a power outage. This ensures the home is always protected, even if somebody borrowed the battery out of the smoke alarm.

You should invest in at least one hard-wired smoke detector on each floor and in the garage of your home. Another benefit to having these devices installed by a Los Angeles electrician is the fact they are all interconnected. When one alarm is sounded, all of the detectors will go off. This means if there is smoke detected in the garage, you will know about it if you are upstairs in your room. These tools can save lives. Give The Electric Connection a call today and schedule your smoke detector installation.