Summer is in full swing which means you’re likely spending more time in a hot tub. If you don’t currently own a hot tub but are considering getting one in the near future, there are some important things to consider before purchasing. It’s a no brainer that water and electricity don’t mix; therefore, adhering to proper safety and electrical protocol with hot tub installation and maintenance is imperative. Listed below are Expert Electric’s 5 tips for hot tub safety:

You might consider yourself to be quite the handyman; however, setting up a brand new hot tub is an entirely different animal. Wiring a hot tub is no easy task and it’s far more complex than setting up your average home appliance. Consulting a licensed electrician for a hot tub installation will often save you time, money, and a trip to the hospital. A licensed electrician will minimize any costly mistakes you would make that could result in permanent damage to the hot tub and a void in the hot tub manufacturer’s warranty. Additionally, they will ensure you’re getting the best value in all of the necessary accessories that need to be purchased for installation.

Although this usually isn’t a problem if your home was built within the past 30-40 years, it’s always a good thing to look into before adding an additional appliance to your home. This is another area that a licensed electrician can help with. It’s also crucial to understand what type of voltage your hot tub is running with. Smaller hot tubs usually require 120 volts whereas larger hot tubs will often run on 240 volts. Understanding the different requirements associated with your specific hot tub’s voltage and how it relays to its power source is key.

When it comes to hot tub installation, it’s all in the wiring. Using the proper wiring is critical to the functioning and safety of your hot tub. It’s important to use wiring that is able to handle the heat. A licensed electrician will be able to answer any questions you have about wiring and determine which type of wiring is necessary for your hot tub.

Did you know that Canada has a set of electrical codes that must be followed when installing and maintaining any type of electrical equipment in Canada? These codes must be followed accordingly during the installation. The Canadian Electric Code is a handbook that can be purchased online; however, it’s a long read and fairly expensive. Hiring a licensed electrician will save you the chore of reading it and void its additional cost.

Before installing a hot tub, it’s imperative to consider its location. You’ll need room for the hot tub as well as extra room to get in and out. The hot tub should be at least 10 feet away from any overhead power lines and 5 feet away from the removed spa panel. It’s also important to consider how the tub will connect to its power source.

For further information on hot tub installation and the necessary electrical requirements, please visit our contact page for a local number near you or to fill out one of our online forms. Our team of licensed electricians are here to help ensure your hot tub gets installed safely and efficiently.

It can be annoying, frustrating and disappointing to decorate for a holiday season, party or event and after everything is set up you discover your outside electrical outlets do not work. The kids are ready to see all the lights or the party planner is near to crying. This was an important time for them and you want to know why the outlets are dead.

What you can do on your own

Is this an unusual occurrence?

Some advertisements for goods on television tell you it has a lifetime guarantee. Very few things are built for lifetime use. Even an electrical outlet can suffer from wear and tear and even environmental circumstances.

While you may have outlets that have protective covers that are supposed to shield them from rain, snow and humidity, dampness can get in and damage your outlet. It could also be that some of the wiring has burned and will not function properly. There is also the possibility that the outlet was not installed by a professional and that it is not up to code.

Before you call your electrician, unplug the cords from the outlets. Do not allow anyone near them or try to do a DIY project. It goes without saying that when you are dealing with electrical problems there could be a danger to you and your family. You want your house to be festive but not burned down.

What will the electrician do?

You repair person will listen to the information you have gathered. He will ensure that the power is shut off to the affected areas prior to opening the outlet to begin work. He will check the actual outlet and the wiring. He will determine whether the problem is limited to the exterior only or if it can or will cause an interruption on the interior of the house.

You’ve heard of bugs in computers? Some types of insects can set up housekeeping behind your electrical outlet and wreak havoc. The repairman will open the outlet after the power it cut and may even have to go into the wall to make a final determination.

He may be able to repair the wiring to the outlet. He will recommend a course of action. It may be that the outlet is damaged beyond repair. Your service person will tell you about the outlets that are available that are identical and also show you others that may be more enhanced or updated. It will be your choice.

If you have ever owned a property with florescent lighting, no doubt you have in some way dealt with a ballast. Fluorescent lights are incredibly common, especially in homes and business buildings. A ballast is a tool that regulates the current in a circuit. For fluorescent lights, it regulates and limits the current running through the tube. Without a ballast, your florescent lighting would not be able to handle being connected to high voltage power. Your lamp would overheat and burn out in a second since the current would increase too quickly.

Commercial lighting is typically more intense than residential lighting. Because of the intensity needed to light up large factories and warehouses, commercial lighting produces a stronger magnetic influence and more heat than the lamps you use at home. If you own a business and have florescent lights installed, it is essential to call a professional Atlanta electrician to handle it. Without the proper light ballast or installation procedure, you could have a fire hazard on your hands.

If you are experiencing flickering or humming coming from your fluorescent light, it could be a warning sign of an old ballast. The typical lifespan of a light ballast is 20 years, but poor light bulbs or cold air can cause the lifespan to reduce greatly.

When a ballast needs to be replaced, and you don’t know what you are doing, it is in your best interest to always call a professional. Electrical work can be incredibly hazardous and if you do not possess the proper training you could severely injure yourself.

Now encroaching into Post-Graduate territory, the 20+ year-old student has a more refined set of needs. Cool isn’t a requirement as much as function. The grad student is faced with the problem of desperately wanting to be a sophisticated adult, but is hindered by full schedules and mounting education costs. Be a hero by giving your favorite 20-something student a gift that acknowledges this new phase of their life: