The strike doesn’t even have to be a direct hit on your home but can occur within half a mile.  As a matter of fact, the majority of surges that most people take are from problems at someone else’s home or somewhere further down on the power company lines.  A surge doesn’t have to be lightning; it can come from an automobile accident that hits a power pole or even from a routine maintenance on the main power lines when they turn the power back on.  This off and on of the power with the main electrical lines can send surges into your home or business that I have seen destroy lots of electronic equipment and appliances.

Almost every home has multiple computers, and expensive home entertainment systems.  Even our appliances are high-tech with monitors built into the doors of refrigerators and laundry appliances with electronic controls.  These items are especially vulnerable to spikes in your home’s electrical current that may cause melted circuit boards and overheated wires.  Repairs to these expensive gadgets are much more costly than replacing a blown out light bulb or electrical outlet.

Demand for the electric cars has been on upward trend over the last few years. However, manufacturers and car owners still face a challenge due to the limited battery capacity which necessitates the need to keep on recharging after traveling a certain distance.

Despite the benefits of charging the electric cars at home, most residential installations, especially the older ones, may not support the systems. But the consumers can upgrade these to accommodate the additional load. The upgrade depends on the existing wiring, panel, capacity and charging station power requirements.

electrical wiring and capacity, and the charger voltage and level. The electric car owner must first decide on the preferred type of charger and time, and then compare its power requirements with the existing capacity at home.

Some chargers require 120V while others work on 240V and each takes different times to fully charge the batteries.  Higher voltages will require dedicated circuits and upgraded wiring, breakers, panel and service entrance.

Other upgrades include the price plan, metering, and compatible outlets or provision for hard-wiring. If you are installing a DC charging is very fast; it uses about 400-volt direct current and is capable of reaching full charge in about 15 minutes. This is a complicated method and may require significant upgrades in the home electrical system. It is also very expensive and rarely used for home charging.

upgrade your wiring or install the product if you system capacity can support it.

It is essential to ensure that the electrical panel and dedicated circuit have the capacity to handle the system. The installation of the charging station is similar to other high power equipment, such as clothes dryer, and should comply with all the electrical codes and requirements.

Each charging station should be on its own dedicated circuit with adequate capacity and protection. However, the it can still be connected to an existing 40 Amp circuit, such as the one for the kitchen, provided that there is a locking mechanism to ensure that only one load is connected at a time.

Charge stations may be hardwired or plug-equipped to connect to the electrical outlet. For the plug type charger, you will need to have an electrician to wire the compatible electrical receptacle according to the codes.

You may add ventilation to improve the cooling of the charge station if it is in a location with poor air circulation.

Charging electric cars at home is the desire of the majority of EV owners. It cuts down on the cost and time to drive and wait at a public charge station. In addition, it does not interfere with the daily activities of the electric car owners since they can charge at night.

Unfortunately, there are several homes without the provision or capacity to support the charging stations. However, the EV owners can consult the car dealers, and then engage qualified electricians in upgrading the existing electrical wiring. This will enable them to conveniently charge at home.

Many homeowners are DIY enthusiasts and will happily fix a broken chair or repaint the living room wall if they feel it’s looking dull and drab. If you are one of those people, you may also be tempted to fix electrical issues when something goes wrong. However, it’s important to keep in view the fact that electrical jobs aren’t for the DIYer. In fact, any electrical job, big or small should be tackled only by a licensed and insured electrician.

When you are working with electricity, safety is something you should never compromise on. It’s a fact that you would be able to handle some simple electrical jobs on your own and they may seem like a breeze, but the truth is that most people aren’t aware of the precautions they should be taking while tackling anything related to electricity.

When it comes to electrical jobs, there is no alternative to hiring an experienced and skilled professional for the job. Take a look at the 6 biggest domestic electrical mistakes novices make:

This is a very common mistake that many inexperienced people make. Every installation needs a different gauge (thickness) of wire. Using the incorrect one in a particular application can result in an overload or overheating in the wire; in turn, this can cause the circuit breaker or fuse to trip. It’s crucial that the wires be rated for the actual amperage they are going to carry.

It’s crucial that you never try to make any electrical connections outside electrical boxes. The sole purpose of these boxes is to ensure that the wires should be protected from external elements. If you do have to make an extension, use a plastic/metal box. Do not shove too many wires into one electrical box- this can lead to a short circuit.

There are times when you may not fix the switches and outlets firmly in the wall. These can be dangerous. When you attempt to fit appliances into an outlet that’s loosely fitted, the wires can come out of their terminals and can get overheated.

All the connections inside a fuse box should be correctly and tightly placed. Loose connections can cause flickering in lights and appliances. At times, it can lead to overheating of circuits too. It’s never a good idea to try to fix these yourself

Circuit breakers and fuses are the safety mechanisms that protect the wire ampacity ratings; they also control the flow of electricity to all the connected appliances. Many people are under the false impression that if a fuse blows or a circuit trips, they can simply replace it; and that the problem will be solved. In actuality, when either of these things happen repeatedly, it’s an indication that there is something wrong in the wiring connected to them. Call in a licensed electrician without delay and get the problem fixed.

This is another common electrical mistake. While many people simply buy adaptors and use them to plug in multiple appliances in at a single point, this only increases the amperage that the circuit can handle. This danger is compounded if you use more than one heavy-duty appliance at a single outlet.

Never take chances when you are dealing with electrical installations or are faced with electrical issues. Always call in a certified electrician to handle the job. For any type domestic electrical installations, call Allround Electrical at 1300 169 263. You can also drop us a line via email.

Thanks for reading,1300 169 263

Sale posters and coupons aren’t the only ways to make sales. You can use lights to your advantage, too. LED retail lighting can be used to create an environment that makes shoppers feel welcome and caters to their needs and expectations. Use LED store lighting to draw people in, to keep them focused, to guide them throughout your store, and to save money. There are so many ways that the right lighting can be beneficial to customer satisfaction and sales. Take a look at the following list of do’s and don’ts to achieve store lighting that will help you reach your goals.

There’s more to effective LED retail lighting than meets the eye. Creating an efficient lighting system that looks how you want while promoting products, making customers feel comfortable, and, in turn, increasing sales involves knowing the technical details of potential bulbs and fixtures. These details include efficacy, color-rendering index (CCT), and intensity.

Intensity/Lumens

In the past, the brightness of incandescent, halogen, fluorescent, or high-intensity discharge (HID) lights was measured by wattage. Now, a common method for measuring brightness is lumens. The higher the lumens, the brighter the bulb. Comparable wattage is always listed on our product pages for compatible products. If you’re upgrading from incandescent to LED and want a bulb or fixture that’s similar in brightness, you can use lumens for an estimate of what incandescent wattage would be. Simply remove the last number of the lumen value. The number that’s left represents estimated incandescent wattage. As an example, an LED light that emits 600 lumens is approximately as bright as a 60-watt incandescent bulb.

Efficacy

As a business owner or manager, you’re most likely concerned with getting the biggest bang for your buck. By paying attention to efficacy, you can make sure that you get the most light for the amount of power the bulb or fixture consumes. Efficacy is the amount of visible light that is produced with a certain amount of power (watts). You can determine the efficacy of a product by dividing its lumens by the watts it consumes. For example, a bulb that emits 480 lumens and consumes eight watts of power (480/8) has an efficacy of 60 lumens per watt. A bulb with this efficacy would be a much better option than one that emits 480 lumens at 12 watts.

CCT

CCT indicates the hue and tone of white light emitted from a specific bulb or fixture. CCT is measured in Kelvins (K), which is similar to degrees in Celsius. Different temperatures on the Kelvin scale represent different colors. For example, light at 2000K-3500K looks more orange/yellow and is called ultra warm or warm white, and as temperature increases in Kelvins, color changes to more of a “paper white” known as natural or neutral white (between 3500K and 5100K) and finally into a bluish-white known as cool white (5100K+).

The color temperature you choose will depend on the mood and shopping experience you want to give your customers. A retailer like Hollister for instance, who strives to create a laid-back, relaxed atmosphere, utilizes warm white and even ultra-warm white lights. Add on the cozy furniture setup and music and it’s clear that the goal is to get customers to hang out, relax, and spend more time in their store. Logic says that the more time you spend in a store, the higher the chances are that you’ll buy something.

Bed Bath and Beyond, on the other hand, uses a different approach to make sales. Their stores are filled with bright natural white light to showcase the wide variety of products that they offer. Customers are going to struggle in a store like BBB if it’s dimly lit. Knowing whether or not a shirt looks good is a lot different than buying new pots and pans. Dim light is flattering and more forgiving when customers are trying on clothes, but it won’t help you read whether or not your pans are dishwasher safe or scratch resistant. The lighting you choose should mesh well with the products you’re trying to sell. Using lighting to set the mood is a great idea so long as that mood doesn’t impact a customer’s ability to shop.

One of any retailer’s main goals when choosing lighting is to make sales. Use light to your advantage when trying to highlight certain things or create visual appeal. Make it obvious where new arrivals or sale items are. Use light to create a path that will guide customers through your entire store. Use LED sign modules for your store window or LED light boxes that feature your products. Anything unique, whether it’s cove lighting, lighting under a set of shelves, decorative light fixtures, or simply how you arrange your lights, is more likely to catch someone’s eye.

There are so many retail lighting options to choose from. Take a look at the list below to see some of the possibilities.

LED tube lights for fluorescent light fixtures

LED strips or puck lights for display case and shelf lighting

Retrofit can lights

Sign modules for store windows or creating custom signs

Canopy lights for outdoor overhangs

If your floor plan is constantly changing, it might be best to install a retail lighting system that can be changed as well. Track lights or gimbal and eyeball can lights can all be aimed in different directions. Depending on the products you’ll be displaying, you might also want to order new bulbs of varying intensities or color temperatures for these fixtures.

There are numerous places that are easy to overlook when planning your retail lighting project. Don’t forget the fitting rooms. This is where shoppers ultimately decide if a clothing item will work for them. Natural or warm white light is best, and a high-CRI LED light will show colors most accurately.

Illuminate aisles to guide customers through the store. Shoppers shouldn’t feel like they’re lost in a maze. Give them a sense of direction to know how to get where they want to go.

Don’t make it hard for customers to leave your store. Use LED light bulbs for exit sign backlighting and spotlighting. These lights are especially important during power outages or in emergencies.

If you’re putting your products on shelves, overhang from other shelves can cause shadows or limit light to the area. LED strip lights are a great solution for this. They have adhesive backings for easy installation, and most can be cut to fit the area that needs lighting. If you’re not crazy about the look of a strip under your shelves or if you want to eliminate hot spots (bright points of light), you can create your own LED strip light fixture using an aluminum channel and diffusing lens.

Make sure the checkout and customer service areas can be found easily in your store. Use different lighting or more lighting to make it stand out. Get creative with LED strip light fixtures around the counter, an edge-lit sign, or a custom-printed LED light box.

You might think that your parking lot has nothing to do with sales, but that is incorrect. If your parking lot is dimly lit, your store is not only less visible, but it’s also not as safe as it could be. A poorly lit parking lot can make customers feel uncomfortable and can lead to accidents. It can also be a problem for capturing security footage.  

blog post for more information.

To see more retail lighting options, visit our commercial lighting category, indoor and outdoor LED lights can also be found in our light box, fixtures, landscape categories.