There are many reasons and advantages of LED street lights over HPS, Metal Halide, and any other HID light used in the street lighting industry. These advantages of LED street range from cost savings, higher quality of light, and overall better efficiency.

LED is quickly becoming the “go to” light for all uses; residential, commercial, and industrial. From fully replacing and retrofitting LED is seriously becoming the majority within the world of lighting. The following list is going to cover 4 major advantages of LED street lights over HPS and Metal Halide, hopefully it shines some light on the true benefits of LED for even Metal Halide, you get results that show LEDs actually really do pay for themselves. If you use your lights often, making the switch to LED street lights may even pay themselves off within a few years.

If you’d like to see how much you could save, check out the diminishes over time. This is a highly important thing to note because with greater lumen depreciation comes added costs of maintenance.

Lighting fixtures such as HPS and Metal Halide have lumen depreciation that happens much earlier in their life and much quicker throughout the bulbs life. Whereas an LED takes a longer time to start depleting in it’s lumen output and much slower lumen depreciation than HPS and Metal Halide does.

While not all LED suppliers and manufacturers, MyLEDLightinGuide.com offers LED fixtures and retrofit kits that can produce at a very high MyLEDLightingGuide retrofit kits can run as high as 151 lumens per watt. While the typical retrofit kits on the marketplace (on average) run at only around 110 lumens per watt.

This is just a prime example of how powerful lumens per watt can be. The more lumens per watt you get, the less watts you will need to produce the same amount of light.

So, let’s compare the “average” retrofit kits compared to a Metal Halide light. Remember, the “average” retrofit kits run at around 110 lumens per watt. Compare that to a Metal Halide light that runs around (on average) 90 lumens per watt.

So just by these numbers we can start to see the power LED lights have and how they need less watts to produce the same amount of light that a HPS or Metal Halide light does.

In addition to #3 on this list, LEDs also provide a higher quality of light measure by the Color Rendering Index (CRI). Here’s two images that should do the talking:

Street Light Conversion From 400W Metal Halide to 120W LED using a LED Retrofit Kit (before)

As you can see after the 400W Metal Halide was replaced by the 120W LED fixture, the light produced is much brighter and illuminates a greater area. On top of that, it is using way less energy (400W down to 120W)!

Brighter and greater illumination can greatly increase safety and reduce crime by the simple fact of being able to see more throughout the night. Better illumination also creates safer roadways by not leaving any dark spots that may cause issues for drivers during night time driving.

Electric cars are becoming very common. If you have visited a car lot lately, you will see the selection has increased dramatically and Prius is no longer the only game in town. It is the future of cars and there is no time like the present to start learning the ropes of using an electric car for your transportation needs. A Santa Monica electrician is here to help you make the most of your new electric car or make your old one a little better with the installation of a Level II charger at your home. The team at The Electric Connection can assist you in getting the most out of your gas-saving car.

One of the problems with electric cars is their inability to drive long stretches on the battery alone. They are great for commuters with short distances to travel. Most electric cars can go anywhere between 40 to 100 miles on a single charge. Unfortunately, it can take a full day for a car to get a full charge when using a Level I battery charger. An electrician in Santa Monica can install the 240-volt outlet you need to run the Level II or fast charger in your own garage. This means, every day you get home from work, you plug in the car and it is fully charged and ready to go the following morning.

The faster chargers are a bit more expensive up front, but when you factor in the gas savings, it is an investment that will pay off over time. It is also more convenient in general. Because the charger requires more electricity to run, you will need an electrician. Santa Monica homeowners can decide where they want to charge their car and have the outlet installed nearby. Give The Electric Connection a call today and schedule your installation.

As a facility manager or building owner, it is nearly impossible to know everything about everything in your building. But it is vital to know something about everything, and that goes for your facilities lighting system too. Whether you manage a warehouse, factory, or other industrial sized building or space, the lighting is a huge factor of many things including safety, productivity, and consistency in the work in your facility.

So while you don’t need to know every facility managers and building owners should know about there lighting system and how lighting can make all the difference in various amounts of ways.

1. Not all lights are created equal. This is an obvious one, not all lighting technologies are created the same and all output at different levels. Firstly you have lighting technologies that are less efficient than others. Such as metal halide and HPS which are 2-3 times less efficient than LED technology is. Then you also have efficiency based on a “product to product” basis. For example; while LED is the clear winner in efficiency over metal halide (and really any other lighting technology), one LED product from one company isn’t going to be the same as the next company’s LED product. This is where you really need to dig deep and find the company that offers the most efficient lighting products over all other companies.

Key takeaway? First, understand that LED is the most efficient in a general sense, but also understand that each company and product varies on its own personal efficiency and you should always do your homework before going with one LED product over another!

2. New lighting system upgrade costs can be reduced with rebates. This is only a true statement when you are buying commercially qualified lighting products that are DesignLights Consortium qualified. return on investment overtime by decreased energy costs associated with running your lights. Obviously this ROI period will vary depending on how long you run your lights per day on average, but especially in big facilities they almost always are used often and thus, provide a good and even quick payback period.

4. Create safer environments with a proper lighting system. With low quality light output, you create an unsafe environment that can cause various issues. Lighting fixtures that aren’t outputting the proper amount of light after a few years into there life is all caused reasoning to retrofit over fully replace.