Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

In the 30 years I’ve been an electrician, I’ve had a lot of time to think about what qualities make the best Dallas Electrician the best.  Obviously, there are a whole lot of factors that go into something like that:  quality of service, friendliness, willingness to help.  But let’s face it; at the end of the day, the best electrician is the one who can save you money.  So, I’d like to share some money saving tips with you.  And I‘m going to start with the biggest, most effective tip of all.  Ready?  Here it comes.

Turn your stuff off

That’s it!  Turning your electrical devices off when you’re not using them is the best way to lower your home electric bill now, I know what you’re thinking:  “That’s not a very fun answer.”  Well, you’re right:  there are certainly more interesting ways to save money on your electric bill (and I’m going to share a few of them with you right now), but it’s important to start with the basics.  So, what can you do to save money without turning things off?

When you plug something into an outlet in your home, you probably don’t really take the time to think about where the electricity to power your appliance comes from. You plug it in, it works. But, what do you do when it doesn’t work?

Homeowners are constantly making improvements to their home. This may include upgrading or installing a new air conditioning unit, replacing the old fridge with a newer, more family-friendly model or adding a hot tub to the backyard. If you have already made these investments or are considering making them, you should contact your electrician. Beverly Hills residents can rely on the professionals at The Electric Connection to provide fast, friendly and knowledgeable service.

An electrical inspection will be needed to determine whether or not your existing electrical panel can handle these much larger items. Hot tubs, AC units and larger power tools will need more power than the typical appliance. If you have a newer home, it is a fairly simple process for an electrician to install the outlet needed to power the new item.

Older homes may need an electrical panel upgrade to support the electricity demands. An additional breaker may need to be added. In fact, this is may apply to newer homes as well, depending on the service that was put in during construction of the home.

If you have already hooked up a new refrigerator or stove and notice you seem to be tripping breakers, it is likely you need an upgrade. This is a sign there is too much draw on a breaker or that a breaker is weak. An electrician in Beverly Hills will be able to determine what the problem is during the inspection. If you are ready to take care of those tripping breakers or have more questions about what it takes to get your new appliance properly wired, give The Electric Connection a call.