LED Lighting Kit. This complete LED strip lighting kit is designed to permanently install on canopy tents, sun shelters, instant canopies, pop-up shelters, or E-Z UP Instant Shelters. A variety of colors are available—including “Bugs-Away” yellow—and the strip lights provide up to 360 lumens of illumination.

Regardless of bends, twists, or turns, Example of a cut line on LED strip lights

2. You will now have two LED strip lights. Carefully peel back the end portion of the paper strip covering the strip’s adhesive backing, and then remove the 3M VHB adhesive from the solder pads on the bottom side of one of the strips. The strip with its adhesive peeled back will be the top strip when soldered.

5. Align the non-tinned strip segment (strip with adhesive removed) directly over the newly tinned pads, and apply heat. Hold the soldering iron in place until the solder remelts and begins to flow. To strengthen the bond and improve visual appeal, a small portion of solder can be added to the top pad.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split and solder a run of non-weatherproof two-conductor or connecting wires. Peel away the blue wire so that only the positive (red), negative (black), and control (green) wires are left.

*No wires should be peeled away if you’re joining single-color or standard RGB light strips.

3. Properly heat your soldering iron. For best results, clean and tin the tip of the iron immediately before soldering. To tin the iron, touch solder to both sides of the iron’s tip.

4. Next you will need to tin the solder pads on both ends of the split strip light. When soldering, always apply heat to the target area on the strip and not directly to the solder. Once sufficient heat has been applied to the area, start introducing solder.

The LED strip lights are now connected, and power should flow through the entire length of the strip.

The following steps demonstrate how to split, solder, and reseal a

3. Follow steps two through five located at the top of this post for soldering a standard RGB strip light.

4. To reseal the strip light, apply

The LED strip lights are now connected, and power should flow through the entire length of the weatherproof strip.

Being the owner of a plant is a big responsibility and it is very important to keep your equipment in working condition. You need to remember that all your maintenance must be planned in an efficient way for both economic and energy efficiency.

Usually when you choose to partake in your routine maintenance, it may cause a delay in your production resulting in loss of income. All safety electrical equipment that is used on a continuous basis will require a lot more maintenance than your equipment that is used rarely, although they will still need to be maintained.

Even though you may maintain your equipment on a regular basis there will be times that your equipment could break. You will then need to take all costs into consideration before deciding whether you should repair the equipment or to just replace it completely.

To help you decide, you should analyze what you have already spent on the equipment as well as what it will cost to maintain it in the future. Once you have done that you should compare it to what it would cost you to acquire newer equipment that may cost less to maintain.

You could also hire a specialist that could create a breakdown of important factors such as the probability of the following:

To run a successful plant you will also need to keep the following important steps in mind:

Whether you have a scheduled lighting project or an emergency on your hands, there are plenty of situations when it’s appropriate to call in a local electrician. For your safety and sanity use a certified electrician that can provide quality work and can be counted on for years to come.

Repairing a Wire Damaged from Drilling a Hole in the WallWhether you’re hanging pictures, shelves or a TV mounting bracket—or any other reason you might be drilling into a wall—there’s always the possibility that you’ll hit and damage a wire. This is definitely a fix you want to leave in the capable hands of a certified electrician.

To prevent the problem from happening again, use a stud finder and aim for the center of the stud. Before drilling, use a small tipped screw driver to verify you are hitting the stud and not the side. Once you have verified, feel free to drill away.

To work with a licensed qualified professional for your next electrical project, please contact a certified electrician at ElectricMan today. ElectricMan is a trusted, local electrician with 27 years of experience. For more information visit the ElectricMan website, and don’t forget to also ‘like’ us on Facebook and follow us on Twitter, YouTube and Pinterest.