When it comes to DIY jobs, electrical wiring is one thing that you should avoid. Most wiring or rewiring jobs are incredibly complex, and require the expertise of trained and licensed professional electricians, such as the members of our staff. You also don’t want to trust this job to an amateur or a general “handyman” as they most likely lack the necessary training to do the job right.

One of the most popular rewiring jobs people choose to proceed with is finishing their basement, which requires a good amount of rewiring throughout. Keep reading to learn more about what this type of job requires, and why you should only trust the professionals to complete it.

Even the smallest drip coming through your below-grade walls can create a problem. You’ll want to have the outside checked to ensure that the ground is graded away from your foundation, and also will want to check for cracks in your foundation walls and have that damage repaired if necessary.

Chances are, you don’t know the local building codes in your area. Many times, you’ll need to get building permits to make any electrical changes to this room of your home, as that room may need to be inspected before the job begins. Our electricians are aware of these rules and will take the necessary steps to ensure the job is done correctly.

A drop, or suspended, ceiling is one that is lower than the natural ceiling of your basement. This allows you to conceal any new plumbing that is put in, as well as electrical components such as wires. The good news is, there are plenty of attractive options for these types of ceilings. This also allows you to give your lighting a recess, which allows you more space for light fixtures.

As tempting as it may be to finish your entire basement, keeping the space housing your HVAC units and water heater clear, open, and unfinished is a good idea. That’s because these spaces have specific code requirements, plus your service professionals will need access for maintenance and repairs.

You’re on top of grounding your children, but are you familiar with grounding your home? It improves the safety of your home as well as increases the life of your electronics, and who doesn’t want that? Mr. Electric has all you need to know in order to have your home properly grounded.

Electricity likes to travel the path of least resistance. When there’s too much of it, it needs somewhere to go. That’s where grounding comes in. You see, without it, that path of least resistance is your appliances and electronics – and possibly you when you use them. Burn! Zap! Not a good thing.

Since you don’t want your appliances – or you – to take the heat in these situations, a grounding wire is added to your home, offering all that electricity the perfect chance of escape, via a wire attached to your home’s electrical system which is submerged firmly in the ground – the reason it’s called “grounding.” Both your home’s electrical box and your home’s outlets need to be connected to this grounding wire in order to be properly and safely grounded.

Without proper grounding, you and your home could suffer burned out electronics and appliances, electrical fires and potentially deadly electrical shock.

Without special testing equipment, it may be difficult to tell. Just because you have three prong outlets does not mean the outlets – or your home – are properly grounded. These outlets must be properly wired in to your home’s main grounding wire for proper protection. There is also more to grounding than sticking a big metal rod in the dirt, such as properly attaching wires, grounding to your home’s water pipes correctly, and much, much more. If you don’t want your electrical behaving badly, you can ensure it is properly grounded by having it inspected by a licensed, qualified electrician.

Newer homes, as a result of increased safety regulations, are typically properly grounded. Older homes, on the other hand, may not have had a proper grounding experience, or any at all. Homes built before 1950 are especially at risk. You should always have your home, regardless of age, inspected for proper grounding by a licensed, qualified electrician to avoid the potential risks of fire, electrical shock, and property damage. You never know what the previous resident did without a permit.

Don’t suffer the punishment of burnt out electronics or a burned down home. Mr. Electric® will keep you out of trouble – get grounded today!

Once someone has discovered retrofitting as a read that by clicking here.

Let’s get started with the first question on the list, and that is what exactly is a retrofit kit?

What is a retrofit kit anyways? Well, we’ve actually reducing your energy consumption even more. Just make sure you are buying a LED retrofit kit that has the option to be dimmable, otherwise you will NOT be able to dim them.

Retrofit vs full replacement, why should you consider retrofitting with LED?

While a full replacement of an entire is fixture is very valid to do especially when they are outdated or literally falling apart; often times you can avoid that by retrofitting your fixtures. With retrofitting you get to keep your old fixture but just replace the light source in it with a new one. This will allow you to reduce the costs associated with the lighting upgrade tremendously, which will allow you to realize a much larger ROI.

Although there are benefits of both, you need to think about your facility or buildings own situation, and go from there. To recap; retrofitting is great if you can keep your old fixtures but if you can’t (due to reasons like outdated or near falling apart), then a full replacement is probably the better option.

For more info, check out this infographic (

Why should I even switch to LED in the first place?

Very good question, and this not only applies to those retrofitting but for any facility that plans to make a lighting system update. LED technology has vast benefits in almost every area of the definition “quality” for commercial lighting purposes. Here are just a few of the major benefits that more often than not win over businesses to commit to the conversion over to LED technology:

As you can see these are all some pretty big benefits, and that’s only the start. These reasons are why many companies are making the conversion over to LED products from other outdated technologies such as metal halide, HPS, and even fluorescent. Why not convert to LED with a retrofit LED kit and realize all of these benefits and more? It just makes sense!

Is it difficult to retrofit an existing light fixture?

Well, that can depend. To someone who has no knowledge about lighting fixtures and electrical wiring, then yes this will seem like an extremely difficult task. On the other hand for someone who is a professional, this isn’t a difficult task at all.

The process, in theory, is simple because all it consists of (for the most part) is a replacement of all the existing lamps, ballasts, sockets, and brackets with new ones to fit your retrofit kits. If you have no experience doing this, and even if you do, it is always recommended to bring in a licensed electrician if you can to ensure it is done right and to safety standards.

Are LED retrofits that are compatible with existing ballasts a good idea?

You need to consider the age of the ballast that is currently installed. In most cases, it will be nearing the end of it’s life and thus it won’t be the most up-to-date ballast that you could have. This adds for an additional point of failure, which could cost you more down the line in maintenance fees to replace them when they die out.

You have to consider that since you are considering the switch over to LEDs through retrofitting, you most likely haven’t recently upgraded you lighting system or replaced much. This means that the ballasts currently installed are most likely, at best, as old as the lights in your fixtures currently. But more often or not, they are even older than that which can definitely mean they are nearing the end of their lifespan.

Taking this all into account, it’s impossible to tell you if using existing ballasts is a contact us. We will gladly answer any question you may have!

If you cannot answer this question with confidence please ask yourself…  WHO DID I JUST LET INTO MY FAMILIES HOME?  Many people have made this mistake and some paid the ultimate sacrifice.  Some just fell victim to theft, such as the scam where a handyman would offer services to gain access into someone’s home and then steal from them.  You can read more about this crime here.  Unfortunately, there have been more victims experiencing much worse crime.  We do not need to get into the details for the purpose of this blog but we have all heard about them on the news, social media and the stories are very easy to find and numerous.

An electrician on drugs is a recipe for disaster.  Yes an electrician on drugs may not intentionally try to harm you, but how many traffic deaths happen every single hour in the US from people under the influence of drugs or alcohol?  You wouldn’t let a person under the influence of drugs or alcohol drive your children to school, so why would you let them perform electrical work in your home?  Our service electrician’s undergo a drug screen and are also subject to random checks throughout the year.

Our service professionals undergo a thorough background check before being hired.  We won’t just send anyone into your home.  We are going to send a true professional that meets our stringent guidelines.  He is not going to steal from you.  He is not going to harm you.  He is there to help you.  Our electricians truly care about you and the work they are performing for you.

We are here to serve YOU, our customer!  We want a customer for life.  We are not here to steal from you or take advantage of anyone!  We are here to provide a VALUABLE service to you.  We will stand behind our work and make sure you are 100% satisfied.  We guarantee it with the way we act in our organizations culture, and also in writing.  If for some reason you are not 100% satisfied please let us know.  We will not leave until we get it right.  It’s our guarantee to you, our valued customer.

Many contractors say that.  You win some you lose some.  Not with us!  No we do not get every job we bid on, but we realize there may be other factors at play.  What we care about is you truly understand the price presented to you.  You know what options and solutions you have.  You know what will be done, how it will be done, and that we will stand behind our work.  You know the value you are getting when you choose Custom Electrical Services.

It’s common to be nervous when a service person shows up to your home.  Your thinking how much is this going to cost me?  Am I getting the best bang for my buck?  Do I have other options?  At Custom Electrical Services, our technicians are trained for this.  We will work to put you at ease and make sure you fully understand everything presented to you.  We will take the time to fully evaluate your situation and present it to you in a professional manner that you can understand.  Price is not everything.  We will not change the price of the work performed.  The straightforward price you receive will not change if it takes our electrician longer than expected.  You won’t be left thinking, “I hope he can work faster so my bill will be less”.  Lets think about this common statement for just a second.  Would you really want a mechanic hurrying up to put new brakes on your families car?  Of course you wouldn’t!  You would want the mechanic to perform the job as best as possible.  And that is our promise to you.  Give you the best possible job and the most reasonable rate possible.  We are professionals.  We are Custom Electrical Services.

But wait!  A Custom Electrical Services technician is not just there to give you an estimate or fix that minor problem you called about.  We are here to truly help you.  When is the last time someone checked the connections in your electrical panel?  1 year, 10, or never?  Electrical connections can loosen over time.  Electricians are trained to look for this.  As part of our service fee we will inspect your breaker box or electrical panel.  Identify any problems such as loose connections, non code compliant breakers, under sized wire, corrosion, heat, and more!  What if you have an old Federal Pacific Panel and you didn’t even release the dangers they present.  Our technician will identify and let you know of any potential safety problems.

Are all of your smoke alarms and carbon monoxide alarms functioning properly?  For no additional charge we will test all your smoke alarm units and identify any that are not functioning properly.  We will also replace all your batteries at the same time.  It is all part of the service designed to keep you, your family, and your home safe.  Our commitment to you!